安徽主保佳新型涂料有限公司,咨询电话:0551-66396238
公司新闻

真石漆的施工流程和真石漆的施工技术指标

日期:2016年7月11日 浏览[982]

真石漆的施工流程:

    12个小时24小时之后打磨喷底油两遍――喷真石漆2-3mm――喷面油两遍

    真石漆的施工技术指标:

    1)打磨:采用400――600目砂纸,轻轻抹平真石漆表面凸起的砂粒即可。注意用力不可太猛,否则会破坏漆膜,引起底部松动,严重时会造成附着力不良,真石漆脱落。

 2)喷涂底油:选用下壶喷枪,压力4-7Kg/平方厘米,施工时温度不能低于10摄氏度,喷涂两遍,间隔2小时,厚度约30微米,常温干燥12小时。
 
   3)喷涂面油:选用下壶喷枪,压力4-7千克/平方厘米,施工不低于10摄氏度,喷涂两遍,间隔2小时,厚度约30微米,完全干燥需7天。

  4)喷涂真石漆:选用真石漆喷枪,空气压力控制在4-7千克/平方厘米,施工温度10摄氏度以上,厚度约2-3mm,如需涂抹两道、三道,则间隔2小时,干燥24小时后方可打磨。
 

 

The construction process of lacquer:

12 hours after 24 hours polishing spray oil two times -- 2-3mm -- lacquer spray spray oil two times
The construction of technical indexes of lacquer:


1) Polish: the 400 -- 600 sandpaper, gently smooth stone raised surface sand can be. Note that force can not be too fierce, otherwise it will destroy the film, caused by the bottom of the loose, serious will result in poor adhesion, imitation stone paint off.


2 spraying bottom oil: the use of lower pot spray gun, pressure 4-7Kg/ square centimeters, the construction temperature can not be less than 10 degrees Celsius, spraying two times, 2 hours interval, the thickness of about 30 microns, room temperature dry 12 hours.


3 spray face oil: the use of the next pot gun, pressure 4-7 kg / square centimeter, the construction is not less than 10 degrees Celsius, spraying two times, 2 hours interval, the thickness of about 30 microns, completely dry for 7 days.


4) spraying truestonepaint: selection of lacquer spray gun, air pressure control in 4-7 kg / cm2, the construction temperature above 10 degrees Celsius, thickness of about 2-3 mm, such as the need to apply two, three, is interval of 2 hours, dry for 24 hours before can be polished.

 

安徽真石漆官方网站:http://www.ahzbj.com

最新内容:



上一篇: 浅谈真石漆的施工设备及要求
下一篇: 合肥主保佳浅谈真石漆施工的底材及要求

安徽新型涂料有限公司 合肥墙绘公司 合肥网络布线版权所有 Copyright  2010 All Right Reserve 免责声明 皖ICP备11002092号 合肥网站制作:合肥网络公司

安徽省合肥市双凤工业园 网址:http://www.ahzbj.com/  网站地图